Fits 009 and 050 Distributors. Probably only the German 009 as we found the magnetic pickup loose on Brazilian 009 shaft.

356 Pre-A ( 50-55 ) This version has 24mm Pitman arm shaft and does not fit 56 and later cars. Before purchasing this part make sure it is correct for your car. Ask us to help you if needed.

This TRANSMISSION HOOP should fit all cars that use late trans mounts 519-20-095 and 519-20-096. 356A, 356B, 356C ( 57-65? )

Outer Rear Wheel Bearing, FAG, 2 required per car, fits 911 with steel trailing arms, 1965-68.

Pinion shaft bearing. 915 Transmission 1970 through 1986.

Spec 2.5-4.5 PSI per Airtex. This pumps current is about 1.6A. These pumps are made by Carter but re-branded Airtex. WARNING! This pump must be running when the engine is running, even when it is used to pump fuel up to carbs. The mechanical pump is not able to pull fuel through this pump.

This RMG design dome style sump plate includes a 14mm drain plug so sump plate does not need to be removed to drain engine case oil. The plate has been powdered painted and ready to install. Includes a drain plug seal ring.

Non-Counter weight Crankshaft for 356 Normal 356A 356B 356C 1956-1965. This crank has been restored by Armondo of Custom Crankshaft Repair back to STD/STD journal diameters. It has also been Balanced, Nitride, micro polished, Oil Galley plugs R&R and mag checks OK.

This used flywheel has never been reground. The seal surface has a small groove that should polish up. Have Jay resurface, polish seal surface and list as Reconditioned.

This is a intake boot 981.

This is a genuine Porsche part. This seal fits on Intercooler and seals it to deck lid so air is forced through Intercooler. 930 (78-89)

Fits Carrera ( 84-89 with A/C )

Fits 996TT 2002 - 2005, 997TT 2007-2012 and 997 GT2 RS

Non S 987(c) clutch kit. Contains: (1) Disc (1) Pressure Plate (1) Release Bearing. Fits Boxster 2005 - 2008 ( 5 SPEED Trans.) Cayman 2007 - 2008 ( 5 SPEED Trans.)

PORSCHE 986, 986 S, 996, 996 C4, 996TT 2000 - 2005

Inner Rear Wheel Bearing 2 required per car. Fits 911/912 1965-1968.

UPPER 911 74-89, 930 75-89, 914 70-76, 924 76-85. We recommend replacing the retaining clip 999.041.102.01 that holds bearing in.

Connecting Line For The Brake Master Cylinder Front 911,912 1968-75. Install into forward master cylinder port and passengers side body hole.

COVERS SHIFT COUPLER. Carrera style with notch for wires. Painted black and does not have a grill openings. Made in Germany. Genuine Porsche.

Deck Lid or Front Hood Release Cable. Solid wire. Genuine Porsche. Fits 911, 912 65-1989

Plastic luggage mat. This formed plastic mat covers the fuel tank on the later cars. Fits 356BT6, 356C.

Front Door Speaker Grille Fits 911, 912E 1974-1982

This is an external solid state volt regulator. PET says fits MOTOROLA/MARCHEL/SEV, 911 up to 1974.

After Catalytic Converter. Fits 993 96-98 ( NOT TURBO ), 996 98-99.

This knock sensor replaces 9966061250 and requires a updated multi-plug. 986, 996, 996TT, 996 GT3. 2 per car.

Genuine Porsche Pro Battery Maintainer Trickle Charger. Connects to Cigarette Lighter. Works with cars where Cigarette is powered with key off. Works with 911 up to 1998.

Fits 944 85.5-91 with head light washers and cruise control.

Fits 997 2005-2012 Cabriolet.

Asymmetricial Headlight Lens, Marked Bosch, H1 European? It has 4 aiming indicators. Fits 911 1965-86 Left hand drive.

Interior Light, Black Bezel Fits 911 1976-98 930 964 993

This part is no longer available Porsche. This is a New Old Stock(NOS) part in its original Porsche Parts box. This light has indicators for Hand Brake, Brake Pad wear and Seat belt warning. Fits CARRERA, 930 1984 - 1989

THIS UNIT CAME OUT OF A USED 1996 993TT AND IS GOOD.

Genuine Porsche. Made in Germany Brake Light Switch on Master Cylinder (3 Pole Connection)